煤氣發電機組的使用說明

　　Instructions for using gas generator sets

　　煤氣發電機使用說明主要包括開機前檢查、點火、供油、啟動、運行維護和停機等步驟。

　　The instructions for using gas generators mainly include steps such as pre startup inspection, ignition, oil supply, start-up, operation and maintenance, and shutdown.

　　1,開機前檢查：包括檢查水位、油位、電池電壓是否正常，機組無漏油、漏水、漏氣現象。確保各部件完好，無漏氣現象，打開進氣閥使空氣進入氣缸內，打開噴油器開關并啟動發動機或踩下油門至底。

　　1. Pre startup inspection: including checking whether the water level, oil level, and battery voltage are normal, and whether the unit has no oil, water, or air leakage. Ensure that all components are intact and free of air leaks. Open the intake valve to allow air to enter the cylinder. Turn on the fuel injector switch and start the engine or press the accelerator to the bottom.

　　2,點火：當火花塞跳火時關閉點火開關。

　　2. Ignition: Turn off the ignition switch when the spark plug jumps.

　　3,供油：根據發動機負荷大小調節供油泵的壓力和流量，當燃油壓力達到規定值時停止供油。

　　3. Fuel supply: Adjust the pressure and flow rate of the fuel supply pump according to the engine load, and stop fuel supply when the fuel pressure reaches the specified value.

　　4,啟動：按下啟動按鈕后發動機開始運轉，待溫度達到80°C以上時方可起步行駛。

　　4. Start: After pressing the start button, the engine starts running and can only start driving when the temperature reaches 80 ° C.

　　5,運行維護：調整控制屏上的電壓調節器的微調旋鈕，使交流電壓表在400V位置。定時檢查發動機油位和水箱水位，注意天然氣機管道是否有漏氣現象。

　　5. Operation and maintenance: Adjust the fine adjustment knob of the voltage regulator on the control screen to keep the AC voltmeter at 400V position. Regularly check the engine oil level and water level in the water tank, and pay attention to whether there is any leakage in the natural gas engine pipeline.

　　6,停機：正常停機應逐步卸去負載并主開關分閘后，將轉速選擇開關置“怠速"位，天然氣發動機機轉速至700r/min。按照天然氣發動機機使用維護說明書的要求對機組進行冷機后，將“停機”旋鈕旋至停機位置，使發動機停止工作。

　　6. Shutdown: Normal shutdown should gradually remove the load and open the main switch. Set the speed selection switch to the "idle" position, and the natural gas engine speed should reach 700r/min. After cooling the unit according to the requirements of the natural gas engine maintenance manual, turn the "shutdown" knob to the shutdown position to stop the engine from working.

　　7,維護保養：機組正常發電后，應對天然氣機、發電機、控制屏等進行監視并定時做好運行狀況記錄，隨時注意電壓、頻率、功率及天然氣發動機監控儀表的指示變化，及時進行合理的調整。

　　7. Maintenance: After normal power generation of the unit, the natural gas engine, generator, control screen, etc. should be monitored and the operating status should be recorded regularly. Attention should be paid to changes in voltage, frequency, power, and the indication of the natural gas engine monitoring instrument at all times, and reasonable adjustments should be made in a timely manner.

　　以上步驟需嚴格按照操作說明進行，以確保煤氣發電機的正常運行和使用壽命。

　　The above steps need to be strictly followed according to the operating instructions to ensure the normal operation and service life of the gas generator.

　　本文由煤氣發電機組提供技術支持，更多的詳細精彩內容請點擊我們的網站http://www.asianelephant.cn/們將會全心全意為您提供滿意的服務。